Seam Quarter

Churn Dash quilt block

Churn Dash quilt block diagram
Churn Dash: 6 × 6 grid, 4 half-square triangles, 8 rectangles and 1 square.

Four half-square triangles sit in the corners, four two-strip units run along the edges and a centre square of fabric A fills the middle, so the dash forms a broken ring.

  • Fabric A background
  • Fabric B dash

Cutting chart

For one 12″ finished block (12½″ with seam allowance). Change the size above for any other.

FabricCut
Fabric Abackground
  • 2 × 4⅞″ squarepair with fabric B: 4 HST units
  • 1 × 4½″ square
  • 4 × 2½″ × 4½″
Fabric Bdash
  • 2 × 4⅞″ squarepaired with fabric A
  • 4 × 2½″ × 4½″

Between 4″ and 24″ these finished sizes put every cut on a ⅛″ ruler line: 4½″, 5¼″, 6″, 6¾″, 7½″, 8¼″, 9″, 9¾″, 10½″, 11¼″, 12″, 12¾″, 13½″, 14¼″, 15″, 15¾″, 16½″, 17¼″, 18″, 18¾″, 19½″, 20¼″, 21″, 21¾″, 22½″, 23¼″, 24″.

Yardage for a whole quilt

Finished quilt: 56″ × 68″ from 20 blocks. Batting at least 64″ × 76″.

FabricBuyStrips across the width
Fabric Abackground1⅞ yd5 × 4⅞″, 8 × 4½″ strips
Fabric Bdash1½ yd5 × 4⅞″, 5 × 4½″ strips
Border⅞ yd6 strips 4½″ wide, joined end to end
Binding⅝ yd7 strips 2½″ wide (double-fold), 260″ joined
Backing (42″ fabric)3¾ yd2 panels 64″ long, 1 horizontal seam; backing 64″ × 76″

Yardage assumes 40″ of usable width, strips cut across the fabric, and 4″ for straightening, rounded up to the next ⅛ yard.

How it goes together

Churn Dash block pulled apart into its sewing rows
  1. Piece the 4 two-strip units first.
  2. Row 1: half-square triangle, two-strip unit, half-square triangle.
  3. Row 2: two-strip unit, square, two-strip unit.
  4. Row 3: half-square triangle, two-strip unit, half-square triangle.
  5. Sew the pieces of each row together, then join the 3 rows.

Printable templates

For hand piecing, or to check a rotary cut against paper: one full-size template for each different shape, with the cutting line solid and the sewing line dashed, at the size in the cutting chart.

Print at 100% (“Actual size”) and measure the 1″ test square before cutting.

Notes on sewing the Churn Dash

Fabric B, the dash, is split between the half-square triangles and one half of each two-strip unit, so it appears as a ring around the centre of fabric A. Strong contrast keeps the ring readable, and when A and B are close in tone, the block turns to a soft, blurred square. Cutting the dash from a directional stripe or a plaid emphasises the rectangles; a solid keeps the shapes clean.

Repeated in rows, the dash pieces from neighbouring blocks line up into a lattice of rectangles and corners across the quilt. Plain alternate squares in fabric A calm the surface, and sashing frames each block. Scrappy versions work well when the dash fabrics change from block to block while the background stays the same, since the shared A holds the quilt together.

  • Sew the four two-strip units first, each one a rectangle of fabric A joined to a rectangle of fabric B, and press the seam toward the darker fabric.
  • Check against the diagram which half of each two-strip unit faces the centre. Turning one the wrong way is the commonest slip and is easy to miss until rows are joined.
  • Press rows 1 and 3 toward the half-square triangles and row 2 toward the centre square, so the seams oppose where the rows meet.
  • The two-strip units and the half-square triangle units must finish at the same width. Measure them against each other before sewing the rows, and trim the larger one.

More nine-patch blocks