The seam-allowance arithmetic behind quilt cutting rules
Every quilter learns to add ½″ to squares, ⅞″ to half-square triangles and 1¼″ to quarter-square triangles. Only the first is exact. This page works out the other two from the geometry, says how far off the rules are, and uses the same arithmetic for the less familiar cases. Every calculator on this site uses these numbers.
Why a triangle needs more than ½″
Adding a ¼″ seam allowance means moving every edge of the finished shape outward by ¼″. For a square that adds ¼″ at each end of a side, ½″ in all. A right-angle triangle has a third edge, the diagonal, and moving that edge outward pushes the two corners at its ends further along the short sides.
The clean way to see it: offsetting every side of a triangle by the same distance makes a larger triangle of the same shape, with the same centre of its inscribed circle and a radius ¼″ larger. For a right isosceles triangle with short sides a, that radius is a(1 − 1/√2), about 0.2929a. Growing it by ¼″ multiplies every side by the same factor, which adds ¼″ ÷ 0.2929 = 0.8536″ to each short side.
Quarter-square triangles are the same shape measured on the long side, which is √2 times longer, so the addition is 0.8536″ × √2 = 1.2071″.
How far off the rules are
| Shape | Rule | Exact | Slack | Why |
|---|---|---|---|---|
| Square or rectangle | finished + ½″ | +0.5000″ | exact | Two ¼″ allowances side by side. |
| Half-square triangle, cut once | finished + ⅞″ | +0.8536″ | +0.0214″ | The diagonal allowance pushes both corners out by ¼″ × √2. |
| Quarter-square triangle, cut twice | finished + 1¼″ | +1.2071″ | +0.0429″ | Measured on the long side, which carries two of those corners. |
| Four-at-a-time half-square triangles | (finished + ⅞″) × √2 | ×√2 +1.2071″ | rounded up, trim | The square’s side becomes the units’ diagonal. |
| Eight-at-a-time half-square triangles | 2 × finished + 1¾″ | 2× +1.7071″ | +0.0429″ | Four two-at-a-time squares sewn as one. |
| No-waste flying geese, large square | width + 1¼″ | +1.2071″ | +0.0429″ | The goose is a quarter-square triangle. |
| No-waste flying geese, small squares | height + ⅞″ | +0.8536″ | +0.0214″ | The sky triangles are half-square triangles. |
The rules always err on the large side, by about 1/47″ for half-square triangles and 1/23″ on the long side of quarter-square triangles. Sewn with a true ¼″ seam, a two-at-a-time unit comes out about 0.021″ larger than it needs to be: invisible, and the reason some patterns say to trim and others do not. A seam that runs a thread wide uses up the slack, which is why the rule works in practice.
Sizes that never land on a ruler line
Anything set on point involves √2, which no ruler marks. The centre of a square-in-a-square block is the block size divided by √2; side setting triangles for an on-point quilt are cut from a square of the block’s diagonal plus 1.2071″; four-at-a-time triangle units from (finished + ⅞″) × √2. The calculators here round those up to the next ⅛″ and say to trim. Everything else on the site is checked against the ⅛″ grid, and a block’s page lists the sizes at which every cut falls on a line.
How the block pages do it
Each block is drawn on a square grid as units: plain squares and rectangles, triangle squares split on one or both diagonals, flying geese, stitch-and-flip corners and squares on point. For a finished size, each unit becomes the pieces above, the pieces are counted across every block in the quilt before they are batched into pairs or fours, and yardage is worked out by cutting strips across 40″ of usable width. The templates are the finished shapes moved out by ¼″ on every side, the same construction as the figure, so they carry the exact allowance rather than the rounded one.